Password recovery Help

Oh man! Ad-blocking software has been detected! :'(

This website is run by the community, for the community... and it needs advertisements in order to keep running. Blocking our ads means your killing our stats!
Please disable your ad-block, or become a premium member to hide all advertisements and this notice.

Can anyone tell me where I am going wrong, I am trying to do a password recovery and all goes well untill the end where I cant get it to reset, It is a cisco 2600 series, I am new to this (FIRT TIME)


monitor: command "boot" aborted due to user interrupt
rommon 1 > confreg 0x2142

You must reset or power cycle for new config to take effect
rommon 2 > reset

System Bootstrap, Version 12.2(7r) [cmong 7r], RELEASE SOFTWARE (fc1)
Copyright (c) 2002 by cisco Systems, Inc.
C2600 platform with 65536 Kby

program load complete, entry point: 0x80008000, size: 0x7e932c
Self decompressing the image : #################################################
################################################################################
################################################################################
################################################################################
################################################################################
###############################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
################################################################################
# [OK]

Restrict

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706



Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-IK2S-M), Version 1

Copyright (c) 1986-2002 by cisco Systems, Inc.
Compiled Tue 03-Sep-02 22:58 by kellythw
Image text-base: 0x80008088, data-base: 0x80E23440


Compliance with U.S. Export Laws and Regulations - Encryption

This product performs encryption and is regulated for export
by the U.S. Government.

This product is not authorized for use by persons located
outside the United States and Canada that do not have prior
approval from Cisco Systems, Inc. or the U.S. Government.

This product may not be exported outside the U.S. an
either by physical or electronic means without PRIOR approval
of Cisco Systems, Inc. or the U.S. Government.

Persons outside the U.S. and Canada may not re-export, resell,
or transfer this product by either physical or electronic means
without prior approval of Cisco Systems, Inc. or the U.S.
Government.

cisco 2620XM (MPC860) processor (revision 0x100) with 53248K/12288K bytes of mem
ory.
Processor board ID JAD0650035L (2411692030)
M860 processor: part number 5, mask 2
Bridging software.
X.25 software, Version
Basic Rate ISDN software, Version 1.1.
1 FastEthernet/IEEE 802.3 interface(s)
1 Serial network interface(s)
1 ISDN Basic Rate interface(s)
32K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (Read/Write)


--- System Configuration Dialog ---

Would you like to enter the initial configuration dialog? [yes/no]: no


Press RETURN to get started!


00:00:08: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up
00:00:08: %LINK-3-UPDOWN: Interface Serial0/0, chan
00:00:09: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, chang
ed state to down
00:00:09: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed sta
te to down
00:00:21: %LINK-5-CHANGED: Interface BRI0/0, changed state to administratively d
own
00:00:22: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0/0, changed state
to down
00:00:22: %SYS-5-RESTART: System restarted --
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-IK2S-M), Version 12.1(17), RELEA

Copyright (c) 1986-2002 by cisco Systems, Inc.
Compiled Tue 03-Sep-02 22:58 by kellythw
00:00:22: %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to administr
atively down
00:00:22: %LINK-5-CHANGED: Interface Serial0/0, changed state to administrativel
y down
Router>enable
Router#copy start run
Destination filename [running-config]?
7133 bytes copied in 2.512 secs (3566 bytes/sec)
mgredigb02#
*Mar 1 00:05:56: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0.40,
changed state to down
*Mar 1 00:05:57: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel1, chang
ed state to down
*Mar 1 00:05:57: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0.41,
changed state to down
*Mar 1 00:05:57: %LINEPROTO-5-UPDOWN: Line protocol on Interface Tunnel2, chang
ed state to down
*Mar 1 00:05:57: %LINK-3-UPDOWN: Interface BRI0/0:1, changed state to down
*Mar 1 00:05:57: %LINK-3-UPDOWN: Interface BRI0/0:2, changed state to down
*Mar 1 00:05:58: %LINEPROTO-5-UPDOWN: Line protocol on Interface
ged state to down
*Mar 1 00:05:58: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0/0:2, chan
ged state to down
mgredigb02#config t
Enter configuration commands, one per line. End with CNTL/Z.
mgredigb02(config)#enable secret cisco
mgredigb02(config)#reset
^
% Invalid input detected at '^' marker.

mgredigb02(config)#config t
^
% Invalid input detected at '^' marker.

mgredigb02(config)#config-register 0x2102
mgredigb02(config)#reset
^
% Invalid input detected at '^' marker.

mgredigb02(config)#^Z
mgredigb02#
*Mar 1 00:09:26: %SYS-5-CONFIG_I: Configured from console by consolereset
Translating "reset"

Translating "reset"
% Unknown command or computer name, or unable to find computer address
mgredigb02#

 

Oh man! Ad-blocking software has been detected! :'(

This website is run by the community, for the community... and it needs advertisements in order to keep running. Blocking our ads means your killing our stats!
Please disable your ad-block, or become a premium member to hide all advertisements and this notice.

I got there in the end.

 

Sorry for the lack of response there, Peter - guess you happened to post at a quiet time, m8. Don't let that put you off in future though

 

How did you do it?