Search Results

Search Again
Page 3 of 5
  1. NetEyeBall
    Post

    auto summary and vlsm problem

    Kobem...To research futher you might want to look at classfull versus classless routing protocols. Rip 1 is a classfull routing protocol which is...
    Post by: NetEyeBall, Dec 11, 2006 in forum: General Cisco Certifications
  2. NetEyeBall
    Thread

    LAB Suggestions

    Here is my lab. Some of which is coming still. What are some suggestions? Does anyone know of a lab book that lists the lab configurations and...
    Thread by: NetEyeBall, Dec 9, 2006, 1 replies, in forum: Routing & Switching
  3. NetEyeBall
    Post

    PASSED :-D

    Congrats! :D
    Post by: NetEyeBall, Dec 8, 2006 in forum: General Cisco Certifications
  4. NetEyeBall
    Post

    Question Concerning Back to Back T1 via CSU/DSU

    LAYER 1 issue. Once I rebuilt the cable and did the config it worked fine!!!!!
    Post by: NetEyeBall, Dec 8, 2006 in forum: Routing & Switching
  5. NetEyeBall
    Post

    Network monitoring/management software question

    I have worked in two NOCS. Compaq used CA TNG Unicenter and Whats Up Gold (which is basically just a graphical ping utility). Currently I work...
    Post by: NetEyeBall, Dec 8, 2006 in forum: General Cisco Certifications
  6. NetEyeBall
    Post

    Question Concerning Back to Back T1 via CSU/DSU

    Yes, assuming I cabled it correctly. I have the correct pin out, but I could have made a mistake when I was constructing it. Since I don't have a...
    Post by: NetEyeBall, Dec 8, 2006 in forum: Routing & Switching
  7. NetEyeBall
    Thread

    Question Concerning Back to Back T1 via CSU/DSU

    Hooked up 2 2620s with CSU/DSU modules. Pinned out a cable for it per instructions. Programmed it for B8ZS, ESF, Internal and Line clocking,...
    Thread by: NetEyeBall, Dec 8, 2006, 4 replies, in forum: Routing & Switching
  8. NetEyeBall
    Post

    static route , default route confusion please help meee

    The 1st diagram for the router in the top left connected to the ISP is not a stub network. You would need to use either static routes or a dynamic...
    Post by: NetEyeBall, Dec 6, 2006 in forum: General Cisco Certifications
  9. NetEyeBall
    Post

    static route , default route confusion please help meee

    Lets start with the default route. A default route is a static route that you define to mean that all traffic goes out to the next hop router...
    Post by: NetEyeBall, Dec 6, 2006 in forum: General Cisco Certifications
  10. NetEyeBall
    Post

    CCNP Questions Home Labs Which Switches and Routers to get?

    This is my lab so far: 2620 with WIC 2T Bri U 2610 with BRI U, and WIC 1T 2511 with two serial ports 2924 with 2 fiber 2509 with two serial...
    Post by: NetEyeBall, Dec 5, 2006 in forum: General Cisco Certifications
  11. NetEyeBall
    Post

    ISDN Simulators?

    Ciscokits has one. I will post the link later this evening. Too bad you don't remember which adtran it was.
    Post by: NetEyeBall, Dec 5, 2006 in forum: General Cisco Certifications
  12. NetEyeBall
    Post

    CCNA 3 Practical

    Do you know how to physically connect a switch to a switch and router to a switch? Do you know why you would trunk? Do you know what...
    Post by: NetEyeBall, Dec 5, 2006 in forum: General Cisco Certifications
  13. NetEyeBall
    Thread

    ISDN Simulators?

    Which one do you all suggest? I see the one offered by ciscokits.com any experience with that?
    Thread by: NetEyeBall, Dec 4, 2006, 3 replies, in forum: General Cisco Certifications
  14. NetEyeBall
    Post

    Subnetting Test

    Wow...ok.
    Post by: NetEyeBall, Dec 4, 2006 in forum: General Cisco Certifications
  15. NetEyeBall
    Post

    Subnetting Test

    1.) 17.46.23.96 255.248.0.0 1. Find the Subnet = 17.40.0.0 2. Find the 1st Usable Host = 17.40.0.1 3. Find the Last Usable Host =...
    Post by: NetEyeBall, Dec 4, 2006 in forum: General Cisco Certifications
  16. NetEyeBall
    Post

    Subnetting Test

    Subnetting Practice Work: 1. Find the Subnet 2. Find the 1st Usable Host 3. Find the Last Usable Host 4. Find the Broadcast Address OR...
    Post by: NetEyeBall, Dec 3, 2006 in forum: General Cisco Certifications
  17. NetEyeBall
    Post

    Subnetting Test

    Yes, you would need to have an ip address and mask on wan interfaces. I am not sure if this is a Cisco Oddity since I have only worked on Cisco...
    Post by: NetEyeBall, Dec 3, 2006 in forum: General Cisco Certifications
  18. NetEyeBall
    Post

    Subnetting Test

    You have Router1, Router2, and Router3 all connected with point to point T1s. Each Router has its own Lan connecting to F0. Router1's Lan needs to...
    Post by: NetEyeBall, Dec 3, 2006 in forum: General Cisco Certifications
  19. NetEyeBall
    Post

    Subnetting Test

    You have Router1, Router2, and Router3 all connected with point to point T1s. Each Router has its own Lan connecting to F0. Router1's Lan needs to...
    Post by: NetEyeBall, Dec 1, 2006 in forum: General Cisco Certifications
  20. NetEyeBall
    Post

    WANTED 2924 24 with 2 gig Face Plate

    :blink I needed that! :biggrin
    Post by: NetEyeBall, Dec 1, 2006 in forum: General Cisco Certifications
Showing results 41 to 60 of 95 Next >
Search Again
Page 3 of 5
Remove Advertisement - Premium Membership
  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Accept Learn More...