cisco 1721

Oh man! Ad-blocking software has been detected! :'(

This website is run by the community, for the community... and it needs advertisements in order to keep running. Blocking our ads means your killing our stats!
Please disable your ad-block, or become a premium member to hide all advertisements and this notice.

I got this from a guy that got it from a guy, you get the idea. I didn't have a console cable so I made one. When i boot it will not allow a break signal or any input at all. I have tried to hard reset from the board inside nothing. I have pulled wics , nothing. hers is everything i get and cant get further than this by pressing anything. I have tried threatening it and , nothing


System Bootstrap, Version 12.2(7r)XM1, RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 2001 by cisco Systems, Inc.
C1700 platform with 32768 Kbytes of main memory

program load complete, entry point: 0x80008000, size: 0x542624
Self decompressing the image : #################################################
################################################## [OK]


Smart Init is enabled
smart init is sizing iomem
ID MEMORY_REQ TYPE
MainBoard 0X00027A80 1721
0X000F3BB0 public buffer pools
0X00211000 public particle pools
0X0002 0X0000DC00 Card in slot 0
0X0038 0X00003C00 Card in slot 1
TOTAL: 0X0033DE30

If any of the above Memory Requirements are
"UNKNOWN", you may be using an unsupported
configuration or there is a software problem and
system operation may be compromised.



Allocating additional 1408152 bytes to IO Memory.
PMem allocated: 28747064 bytes; IOMem allocated: 4807368 bytes

Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706



Cisco Internetwork Operating System Software
IOS (tm) C1700 Software (C1700-Y-M), Version 12.3(1a), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2003 by cisco Systems, Inc.
Compiled Fri 06-Jun-03 20:01 by dchih
Image text-base: 0x80008120, data-base: 0x809DA464

cisco 1721 (MPC860P) processor (revision 0x100) with 28073K/4695K bytes of memor
y.
Processor board ID FOC07180K2Z (2930095936), with hardware revision 0000
MPC860P processor: part number 5, mask 2
Bridging software.
X.25 software, Version 3.0.0.
1 FastEthernet/IEEE 802.3 interface(s)
1 Serial network interface(s)
1 Serial(sync/async) network interface(s)
1 terminal line(s)
32K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (Read/Write)
This command has no effect on this line; use modem AT commands instead
This command has no effect on this line; use modem AT commands instead



Press RETURN to get started!


*Mar 1 00:00:06.703: %SCM-3-SCM_BAD_SPEED: The modem line only supports a speed
of 115200.
*Mar 1 00:00:07.355: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to
up
*Mar 1 00:00:07.355: %LINK-3-UPDOWN: Interface Serial0, changed state to down
00:00:08: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed
state to down
00:00:08: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0, changed state
to down
00:00:09: %SYS-5-CONFIG_I: Configured from memory by console
00:00:10: %LINK-5-CHANGED: Interface Async2, changed state to reset
00:00:11: %SYS-5-RESTART: System restarted --
Cisco Internetwork Operating System Software
IOS (tm) C1700 Software (C1700-Y-M), Version 12.3(1a), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2003 by cisco Systems, Inc.
Compiled Fri 06-Jun-03 20:01 by dchih
00:00:11: %SNMP-5-COLDSTART: SNMP agent on host 0030-Independence is undergoing
a cold start
00:00:13: %LINK-3-UPDOWN: Interface Async2, changed state to down
00:00:14: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed
state to up
00:00:21: %SCM-3-SCM_BAD_SPEED: The modem line only supports a speed of 115200.
00:00:21: %SCM-3-SCM_BAD_SPEED: The modem line only supports a speed of 115200.
00:00:21: %SCM-3-SCM_BAD_SPEED: The modem line only supports a speed of 115200.
00:00:21: %SCM-3-SCM_BAD_SPEED: The modem line only supports a speed of 115200.
00:00:21: %SCM-3-SCM_BAD_SPEED: The modem line only supports a speed of 115200.
00:00:21: %SCM-3-SCM_BAD_SPEED: The modem line only supports a speed of 115200.
00:00:21: %SCM-3-SCM_BAD_SPEED: The modem line only supports a speed of 115200.
00:00:21: %SCM-3-SCM_BAD_SPEED: The modem line only supports a speed of 115200.

And thats where we stop

 

Oh man! Ad-blocking software has been detected! :'(

This website is run by the community, for the community... and it needs advertisements in order to keep running. Blocking our ads means your killing our stats!
Please disable your ad-block, or become a premium member to hide all advertisements and this notice.

umm first thing to check is that the application (HyperTerminal im guessing) are you connecting using 9600 as the baud rate - and is that the speed set on the actual router itself? and get a proper console cable i think this might be the problem as well.

btw to break the boot sequence you need to press Ctrl-Break before the image starts loading.

but i aint no expert so just try it out...

 

ditto above, and below URL gives the different break sequence commands for the different terminal emulator programs out there
http://www.cisco.com/en/US/products/hw/routers/ps133/products_tech_note09186a0080174a34.shtml